[問題] TP LINK 841ND 無法進登入頁面

看板Broad_Band (寬頻網路)作者 (papipupepon~)時間13年前 (2013/05/14 23:54), 編輯推噓1(104)
留言5則, 4人參與, 最新討論串1/1
剛剛爬過文,不過沒看到相關解答, 只好PO文麻煩大家看有沒有辦法解決! 841ND本來用的好好的~突然無法上網(可是有IP位址) 想說鍵入192.168.2.1到設定頁面 (因為前面還有一台ASUS的機子) 無法出現登錄畫面(就是輸入admin的頁面) 出現 Username or Password is incorrect,reset 的頁面 RESET之後 鍵入192.168.1.1 也沒出現要輸入admin的登入介面 直接就跳到設定的畫面 但是一更改使用者名稱密碼 或是 改IP位置 還是出現 Username or Password is incorrect,reset 的頁面 請問這台機子還有救嗎?? 我是買V7版本的 應該還在保固內 想說不知道自己更新軔体會不會好~還是建議送修(但發票都不見了) 機器資訊(買來都沒動過) 韌體版本: 3.11.7 Build 100716 Rel.72021n 硬體版本: WR841N v6/v7 00000000 麻煩知道的人幫忙解答一下~感恩~~ PS.有推薦的分享器嗎?看來該買台新的頂著用了~ 下面是出現錯誤頁面的完整資訊 Username or Password is incorrect. Please refer to the troubleshooting below: Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again. Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". Note: The settings will be restored to factory default after the resetting. How to restore the device to the factory default settings? Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings. -- ※ 發信站: 批踢踢實業坊(ptt.cc) ◆ From: 114.25.178.186

05/15 00:01, , 1F
wan線不要插 再設定看看。
05/15 00:01, 1F

05/15 02:02, , 2F
感覺連到別台機器 單獨用有線連看看
05/15 02:02, 2F

05/15 22:30, , 3F
樓上2種方法都試過說~~無效!
05/15 22:30, 3F

05/15 23:45, , 4F
不好意思我確認一下,你所說得 "reset" 動作是確實有完成在
05/15 23:45, 4F

05/15 23:47, , 5F
"開機時按住reset按鈕超過五秒而後機器重開" 的完整動作嘛?
05/15 23:47, 5F
確定是有 我用尖的東西 壓reset約10秒 然後全部的燈都亮 裡面全部資了都清空了 (但是 還是沒出現輸入 帳密 的畫面) 今天是連reset後 也出現錯誤的英文網頁 只好寄去送修了~~~感謝大家.... PS.推薦的無線分享器嗎?(不刷新韌體也穩的的) ※ 編輯: brian718 來自: 114.25.178.186 (05/16 22:41)
文章代碼(AID): #1HabuzSP (Broad_Band)
文章代碼(AID): #1HabuzSP (Broad_Band)